▼

Contractor Classifications

Show All Answers

1. Building Contractor

"Building Contractor" means a contractor whose services are limited to construction of commercial buildings and single-dwelling or multiple-dwelling residential buildings, which commercial or residential buildings do not exceed three stories in height, and accessory use structures in connection therewith or a contractor whose services are limited to remodeling, repair, or improvement of any size building if the services do not affect the structural members of the building.

2. Carpentry Contractor

"Carpentry Contractor" means a contractor whose services are generally limited to fabrication and installation of any wood product in a structure including, but not limited to rough framing, structural and nonstructural work, trusses, sheathing, paneling, trim, cabinetry, doors and windows (including metal) and all hardware incidental thereto. May not contract for concrete, masonry, roofing, dry wall or other work not listed. This contractor may not act as the prime contractor or secure permits for any structure, but may subcontract work from other contractors.

3. Class A Air-Conditioning Contractor

"Class A Air-Conditioning Contractor" means a contractor whose services are unlimited in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system only to the extent such duct work is performed by the contractor as is necessary to make complete an air-distribution system, boiler and unfired pressure vessel systems, and all appurtenances, apparatus, or equipment used in connection therewith, and any duct cleaning and equipment sanitizing which requires at least a partial disassembling of the system: to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, piping, insulation of pipes, vessels and ducts, pressure and process piping, and pneumatic control piping; to replace, disconnect, or reconnect power wiring on the load side of the dedicated existing electrical disconnect switch; to install, disconnect, and reconnect low voltage heating, ventilating, and air-conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor shall also include any excavation work incidental thereto, but shall not include any work such as liquefied petroleum or natural gas fuel lines within buildings, potable water lines or connections thereto, sanitary sewer lines, swimming pool piping and filters, or electrical power wiring.

4. Class B Air-Conditioning Contractor

"Class B Air-Conditioning Contractor" means a contractor whose services are limited to 25 tons of cooling and 500,000 Btu of heating in any one system in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system only to the extent such duct work is performed by the contractor as is necessary to make complete an air-distribution system being installed under this classification, and any duct cleaning and equipment sanitizing which requires at least a partial disassembling of the system; to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, piping and insulation of pipes, vessels, and ducts; to replace, disconnect, or reconnect power wiring on the load side of the dedicated existing electrical disconnect switch; to install, disconnect, and reconnect low voltage heating, ventilating, and air-conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor shall also include any excavation work incidental thereto, but shall not include any work such as liquefied petroleum or natural gas fuel lines within buildings, potable water lines or connections thereto, sanitary sewer lines, swimming pool piping and filters, or electrical power wiring.

5. Commercial Pool/Spa Contractor

"Commercial Pool/Spa Contractor" means a contractor whose scope of work involves, but is not limited to, the construction, repair, and servicing of any swimming pool, or hot tub or spa, whether public or private, or otherwise, regardless of use. The scope of work includes the installation, repair, or replacement of existing equipment, and cleaning or equipment sanitizing which requires at least a partial disassembling, excluding filter changes, and the installation of new pool/spa equipment, interior finishes, the installation of package pool heaters, the installation of all perimeter piping and filter piping, and the construction of equipment rooms or housing for pool/spa equipment, and also includes the scope of work of a swimming pool/spa servicing contractor. The scope of such work does not include direct connections to a sanitary sewer system or to potable water lines. The installation, construction, modification, or replacement of equipment permanently attached to and associated with the pool or spa for the purpose of water treatment or cleaning of the pool or spa requires licensure; however, the usage of such equipment for the purposes of water treatment or cleaning shall not require licensure unless the usage involves construction, modification, or replacement of such equipment. Water treatment that does not require such equipment does not require a license. In addition, a license shall not be required for the cleaning of the pool or spa in any way that does not affect the structural integrity of the pool or spa or its associated equipment.

6. Concrete/Masonry Contractor

"Concrete / Masonry Contractor" means a contractor whose services are generally limited to selecting, cutting and laying brick or other baked clay products, or concrete block or other unit masonry products, or pre-cast block, structural glass brick or block; and to pouring, placing and finishing concrete flatwork including placement of edge forms, mesh reinforcement and plastic vapor barriers incidental thereto. This contractor may not secure permits except for the construction of a fire place, wall, slab only or other similar construction where no enclosed or covered structured is to be constructed.

7. Concrete Placing and Finishing Contractor

"Concrete Placing and Finishing Contractor" means a contractor whose services are generally limited to pouring, placing and finishing concrete flatwork (floors, slabs on grade, sidewalks, etc.) including placement of edge forms, mesh reinforcement and plastic vapor barriers incidental thereto.

8. Dry Wall Contractor

"Dry Wall Contractor" means a contractor whose services are limited to the installation of metal studding for non-load bearing interior partitions in connection with dry wall application and the application and finishing of dry wall boards, including sprayed finishes.

9. Electrical Contractor

"Electrical Contractor" means a person who conducts business in the electrical trade field and who has the experience, knowledge, and skill to install, repair, alter, add to, or design, in compliance with the law, electrical wiring, fixtures, appliances, apparatus, raceways, conduit, or any part thereof, which generates, transmits, transforms, or utilizes electrical energy in any form, including the electrical energy in any form, including the electrical installations and systems within plants and substations, all in compliance with applicable plans, specifications, codes, laws, and regulations. The term means any person, firm, or corporation that engages in the business of electrical contracting under an express or implied contract; or that undertakes, offers to undertake, purports to have the capacity to undertake, or submits a bid to engage in the business of electrical contracting; or that does itself or by or through others engage in the business of electrical contracting.

10. General Contractor

"General Contractor" means a contractor whose services are unlimited as to the type of work which he or she may do, who may contract for any activity requiring license under this part, and who may perform any work requiring license under this part, except as otherwise expressly provided in s. 489.113.

11. Insulation Contractor

"Insulation Contractor" means a contractor whose services are limited to installation or placement of insulation in walls, attics, etc. in compliance with the Florida Model Energy Code.

12. Masonry Contractor

"Masonry Contractor" means a contractor whose services are generally limited to selecting, cutting and laying brick or other baked clay products, or concrete block or other unit masonry products, or pre-cast block, structural glass brick or block. This contractor may not secure permits except for the construction of a fire-place, wall or other similar construction where no enclosed or covered structure is to be constructed.

13. Mechanical Contractor

"Mechanical Contractor" means a contractor whose services are unlimited in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, central air conditioning, refrigeration, heating, and ventilating systems, including duct work in connection with a complete system only to the extent such duct work is performed by the contractor as is necessary to make complete an air-distribution system, boiler and unfired pressure vessel systems, lift station equipment and piping, and all appurtenances, apparatus, or equipment used in connection therewith, and any duct cleaning and equipment sanitizing which requires at least a partial disassembling of the system; to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, piping, insulation of pipes, vessels and ducts, pressure and process piping, pneumatic control piping, gasoline tanks and pump installations and piping for same, standpipes, air piping, vacuum line piping, oxygen lines, nitrous oxide piping, ink and chemical lines, fuel transmission lines, and natural gas fuel lines within buildings; to replace, disconnect, or reconnect power wiring on the load side of the dedicated existing electrical disconnect switch; to install, disconnect, and reconnect low voltage heating, ventilating, and air conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor shall also include any excavation work incidental thereto, but shall not include any work such as liquefied petroleum gas fuel lines within buildings, potable water lines or connections thereto, sanitary sewer lines, swimming pool piping and filters, or electrical power wiring.

14. Plumbing Contractor

"Plumbing Contractor" means a contractor whose contracting business consists of the execution of contracts requiring the experience, financial means, knowledge, and skill to install, maintain, repair, alter, extend, or, when not prohibited by law, design plumbing. A plumbing contractor may install, maintain, repair, alter, extend, or, when not prohibited by law, design the following without obtaining any additional local regulatory license, certificate, or registration: sanitary drainage or storm drainage facilities; venting systems; public or private water supply systems; septic tanks; drainage and supply wells; swimming pool piping; irrigation systems; or solar heating water systems and all appurtenances, apparatus, or equipment used in connection therewith, including boilers and pressure process piping and including the installation of water, natural gas (excluding liquid petroleum gases), and storm and sanitary sewer lines; and water and sewer plants and substations. The scope of work of the plumbing contractor also includes the design, when not prohibited by law, and installation, maintenance, repair, alteration, or extension of airpiping, vacuum line piping, oxygen line piping, nitrous oxide piping, and all related medical gas systems; fire line standpipes and fire sprinklers to the extent authorized by law; ink and chemical lines; fuel oil and gasoline piping and tank and pump installation, except bulk storage plants; and pneumatic control piping systems, all in such a manner as to comply with all plans, specifications, codes, laws, and regulations applicable. The scope of work of the plumbing contractor shall apply to private property and public property, shall include any excavation work incidental thereto, and shall include the work of the specialty plumbing contractor. Such contractor shall subcontract, with a qualified contractor in the field concerned, all other work incidental to the work but which is specified herein as being the work of a trade other than that of a plumbing contractor. Nothing in this definition shall be construed to limit the scope of work of any specialty contractor certified pursuant to s.489.113(6).

15. Residential Contractor

"Residential Contractor" means a contractor whose services are limited to construction, remodeling, repair, or improvement of one-family, two-family, or three-family residences not exceeding two habitable stories above no more than one uninhabitable story and accessory use structures in connection therewith.

16. Residential Pool/Spa Contractor

"Residential Pool/Spa Contractor" means a contractor whose scope of work involves, but is not limited to, the construction, repair, and servicing of any residential swimming pool, or hot tub or spa, regardless of use. The scope of work includes the installation, repair, or replacement of existing equipment, any cleaning or equipment sanitizing which requires at least a partial disassembling, excluding filter changes, and the installation of new pool/spa equipment, interior finishes, the installation of package pool heaters, the installation of all perimeter piping and filter piping, and the construction of equipment rooms or housing for pool/spa equipment, and also includes the scope of work of a swimming pool/spa servicing contractor. The scope of such work does not include direct connections to a sanitary sewer system or to potable water lines. The installation, construction, modification, or replacement of equipment permanently attached to and associated with the pool or spa for the purpose of water treatment or cleaning of the pool or spa requires licensure; however, the usage of such equipment for the purposes of water treatment or cleaning shall not require licensure unless the usage involves construction, modification, or replacement of such equipment, or the replacement of such equipment. Water treatment that does not require such equipment does not require a license. In addition, a license shall not be required for the cleaning of the pool or spa in any way that does not affect the structural integrity of the pool or spa or its associated equipment.

17. Roofing Contractor

"Roofing Contractor" means a contractor whose services are unlimited in the roofing trade and who has the experience, knowledge, and skill to install, maintain, repair, alter, extend, or design, when not prohibited by law, and use materials and items used in the installation, maintenance, extension, and alteration of all kinds of roofing, waterproofing, and coating, except when coating is not represented to protect, repair, waterproof, stop leaks, or extend the life of the roof.

18. Sheet Metal Contractor

"Sheet Metal Contractor" means a contractor whose services are unlimited in the sheet metal trade and who has the experience, knowledge, and skill necessary for the manufacture, fabrication, assembling, handling, erection, installation, dismantling, conditioning, adjustment, insulation, alteration, repair, servicing, or design, when not prohibited by law, of ferrous or nonferrous metal work of U.S. No. 10 gauge or its equivalent or lighter gauge and of other materials, including, but not limited to, fiberglass, used in lieu thereof and of air-handling systems, including the setting of air handling equipment and reinforcement of same, the balancing of air-handling systems, and any duct cleaning and equipment sanitizing which requires at least a partial disassembling of the system.

19. Specialty Contractor

"Specialty Contractor" means a contractor whose scope of work and responsibility is limited to a particular phase of construction and whose scope is limited to a subset of the activities described in the categories established in one of the listed categories.

20. Specialty Structure Contractor

"Specialty Structure Contractor" means a contractor whose scope of work and responsibility are limited to the execution of contracts requiring the experience, knowledge and skill necessary for the fabrication, assembling, handling, erection, installation, dismantling, adjustment, alteration, repair, servicing and design work when not prohibited by law in accordance with accepted engineering data and/or according to manufacturers specifications in the aluminum, metal, canvas, vinyl and fiberglass screening, and allied construction materials. The scope of such work shall include and be limited to fabric coverings on metal substructures, screened porches, screened enclosures, pool enclosures, preformed panel-post and beam roofs, mobile home panel roof-overs, residential glass window and door enclosures, vinyl panel window enclosures, single story self-contained aluminum utility storage structures (not to exceed 500 sq. ft.), siding soffit, fascia and gutters. The scope of such work shall include woodwork incidental to the aluminum and allied materials construction work. It shall be limited to the construction of wood framing for the walls of uninhabitable utility storage structures, raised wood decks for enclosures, and the repair and/or replacement of wood incidental to the installation of siding, soffit, fascia, gutters and preformed panel-post and beam roofs. The scope of such work shall include masonry concrete work and be limited to foundations, slabs and block kneewalls incidental to the aluminum and allied construction materials construction work. The specialty structure contractor, whose services are limited, shall not perform any work that alters the structural integrity of the building including but not limited to roof trusses, lintels, load bearing walls and foundations. The specialty structure contractor shall subcontract, with a license qualified contractor in the field concerned, all other work incidental to that which is defined herein but which is the work of a trade other than that of a specialty structure contractor. Nothing in this definition shall be construed to limit the scope of work of any specialty contractor certified pursuant to s.489.105 (3) and 489.113 (6).

21. Stucco, Lath and Plastering Contractor

"Stucco, Lath and Plastering Contractor" means a contractor whose services are limited to application or installation of these materials: stucco, simulated brick or stone, metal lath including studs and runners to which metal lath is applied, materials for waterproofing and cosmetic work.